Why RT60 Determines Sound Quality in an Auditorium
RT60 is the time it takes a sound to decay by 60 decibels after the source stops. It is not a theoretical number. Every person sitting in the room, whether speaking or listening, feels its effect directly.
When RT60 is too long, reflections from walls, ceiling, and floor keep traveling through the space after the original sound has ended. The next word then overlaps with the leftover reflections of the previous one. The result is a muddy, reverberant sound. Listeners at the back lose the thread of a sentence and start to feel the room as noisy, even when the PA volume has been turned down.
A RT60 that is too short creates a different but equally damaging problem. The room sounds dead. Speakers have to push harder because there is no natural room support. In a music performance, notes feel disconnected and harmonics lose their fullness. Large rooms with an RT60 below 0.7 seconds are uncomfortable for anyone speaking or performing in them.
This is why acoustic treatment in an auditorium is not a matter of putting up material and calling it done. Every material choice, every square meter of surface treated, and every panel position has a direct effect on the final RT60 value. Over-treating a room is as damaging as not treating it at all.
What Is the Correct RT60 Target for an Auditorium or Multipurpose Hall?
The ideal RT60 for a multipurpose hall falls between 1.0 and 1.4 seconds at mid frequencies (500 Hz to 1000 Hz). When the primary use is speech or seminars, the target tightens to 0.8 to 1.1 seconds to keep word clarity intact. For orchestral music concerts, the ideal RT60 is 1.5 to 1.8 seconds. A target of 1.2 seconds gives the best balance for a hall used for both speech and music.
These figures apply at mid frequencies and must be read alongside room volume. A hall with a volume below 3,000 cubic meters is easier to control and can be pushed toward the lower end of the range. A large auditorium with a volume above 5,000 cubic meters naturally trends toward longer reverberation times and requires more absorption area to bring it down to the target.
The difference in targets between speech-based and music-based use is not a matter of preference. It is a matter of how sound physically works. Consonants such as “s,” “k,” and “t” need clean gaps between them so the brain can distinguish them. A reverberant room blurs those consonants before they reach the listener’s ear. Orchestral music, by contrast, depends on room reflections to build the density of tone that makes it sound full. Without sufficient RT60, an orchestra sounds thin.
Standard references commonly used on building-scale projects include ISO 3382-1 for the acoustic performance of performance spaces, and ANSI S12.60, which is more specific to speech-based spaces such as seminar halls and classrooms. Both documents provide a measurement framework that can serve as the basis for technical specifications in construction contracts.
For a hall that also functions as a seminar room acoustic treatment space, the RT60 target needs to be held more tightly toward the lower end of the range, because speech clarity is the primary priority, unlike a hall that occasionally hosts performing arts events.
How to Calculate and Measure Room Reverberation Time
Reverberation time is calculated using the Sabine formula: RT60 = 0.161 x (V / A), where V is the total room volume in cubic meters and A is the total sound absorption from all wall, floor, and ceiling surfaces. Field measurement is done using an IEC-standard sound level meter with an impulsive test sound source or a pink noise sweep, run in both the empty hall condition and at full audience occupancy.
The Sabine formula works well for rooms with normal proportions and an even distribution of absorptive materials. For very large or irregularly shaped rooms, the Eyring formula or software-based simulation tools such as ODEON or EASE produce more accurate results because they account for room geometry in three dimensions.
One factor that is frequently overlooked in the planning stage is the difference in RT60 between an empty room and a full room. Human bodies and clothing act as sound absorbers with a significant NRC (Noise Reduction Coefficient) value. A 500-seat hall at half capacity can have an RT60 that is 0.2 to 0.4 seconds shorter than the same hall empty. If calculations are only run for the empty condition, the final design can miss the target by a wide margin.
This is why seat specification in an auditorium is not purely an aesthetic decision. Heavily padded seats have a higher absorption coefficient and help compensate for some of the audience’s role, so RT60 does not shift drastically between a full house and a half-full one. This detail is often missed in the coordination between the interior architect and the acoustic consultant.
For auditorium hall acoustic services at building scale, field measurement is still necessary even when design simulation has been done from the start, because the actual performance of installed building materials often differs from the values in the design drawings.
The Multipurpose Hall Problem: Balancing Speech and Music Performance
A multipurpose hall is the hardest space to optimize acoustically, precisely because it has to serve multiple functions. Plenary sessions and graduation ceremonies require clean word articulation. A performing arts show or choir concert requires a livelier room so harmonies blend together.
The most common approach is hybrid acoustic design: target an RT60 around 1.1 to 1.2 seconds, then add elements that can be adjusted manually or mechanically. Variable acoustic panels that open to reveal a reflective surface behind them are one option. Heavy acoustic curtains that can be drawn across to add absorption area during speech use are another.
A second approach is to separate acoustic zones through layout. The ceiling above the stage is made more reflective to support natural sound reinforcement, while side and rear walls receive a greater proportion of absorptive panels. This way, sound energy from the stage still benefits from nearby reflections, but it does not keep reverberating all the way to the back rows.
What to avoid is a compromise that ends up being suboptimal for both functions: RT60 too long for speech, too short for a full orchestra. This outcome is common when design is done without acoustic simulation and relies instead on generic standards that have not been adjusted for the specific volume and geometry of the room.
The Technical Steps to Correct an RT60 That Is Too Long or Off Target
When field measurement shows RT60 exceeding the target, the correction follows this sequence:
- Identify the problem frequency band. RT60 does not need to be corrected equally across all frequencies. The main issue is often in the mid range (500 Hz to 2000 Hz) or the low range (125 Hz to 250 Hz). Each requires a different material approach.
- Add mid-to-high frequency absorption area. Porous acoustic panels using high-density Rockwool or Glasswool at 50 mm thickness and a minimum density of 60 kg/m³ absorb effectively from 500 Hz upward. These panels can be mounted on side walls or hung from the ceiling as cloud panels.
- Address bass boom separately. Low frequencies require thicker bass traps, typically panels with an air cavity behind them (resonator panels) or 100 mm Rockwool positioned in room corners. Thin foam does not reach these frequencies at all.
- Add diffusers to scatter reflected energy. Wood slat diffusers or QRD diffusers on rear and side walls prevent strong echo without removing too much total sound energy. This keeps the room from feeling dead after absorption has been added.
- Check the floor and seating. Thick carpet in the audience area absorbs mid frequencies significantly. A combination of carpet and padded seats can reduce RT60 in the empty condition without requiring a large number of wall panels.
- Install perforated acoustic ceiling. Perforated gypsum ceiling with a Glasswool backing reduces RT60 consistently across the room without compromising the interior finish.
This sequence matters because the common mistake made by non-specialist contractors is to cover every wall surface with panels before calculating how much absorption area is actually needed. The result is an over-treated room that sounds dead and requires remediation work that costs more than the original installation.
Installation work in a large-building auditorium also comes with its own site constraints: material access through service lifts, coordination around the hall’s operating schedule, and ceiling-height installation that requires scaffolding that meets safety requirements. These are considerations that only a large-building auditorium acoustic contractor experienced in institutional project environments can manage reliably.
The Evaluation and Consultation Process for Auditorium Acoustics
The process begins with a site survey to measure existing RT60, map room volume, and identify problem reflection points. The survey is free for projects located in the Jabodetabek area. For projects outside Jabodetabek, the team can coordinate visit schedules and logistics by prior agreement.
Once field data is collected, the engineering team prepares a design simulation covering the RT60 target per frequency band, material specifications including type, density, thickness, and installation area, and a projected estimate of the changes expected. Design work and consultation carry no separate charge.
Construction work is scheduled around the building’s operating hours. After installation is complete, RT60 is measured again to verify the result against the original target. The team also carries out periodic checks for up to six months after project completion.
FAQ: Reverberation Time and Auditorium Acoustics
- What happens if the RT60 in an auditorium is too long?
- Reflected sound piles on top of new sound coming from the speakers. The speaker’s words become indistinct, consonants are lost, and listeners at the back of the room experience fatigue and a sense of noise even when the volume level is not high.
- Is a reverberation time that is too short also a problem for auditoriums?
- Yes. An RT60 below 0.7 seconds in a large hall makes the room feel dead. Speakers and singers have to work harder because there is no natural room support, and music sounds thin and dry.
- Why does RT60 measured in an empty auditorium differ from RT60 when the hall is full?
- Human bodies and clothing act as sound absorbers with a significant NRC value. A large audience can reduce RT60 by 0.2 to 0.4 seconds. Acoustic calculations must account for the absorption coefficient of padded seats and expected audience occupancy.
- Can covering all the walls with foam fix an RT60 problem?
- No. Thick foam on every wall only absorbs high and upper-mid frequencies. Low-frequency bass boom continues to reverberate. A correct solution requires a combination of absorber panels, bass traps, and diffusers.
- How does the Dewa Peredam Ruangan team help measure RT60 for a project?
- The engineering team maps room volume, tests existing frequency response and RT60 on site, then designs absorber and reflector panel specifications matched to the room’s intended function. Free site surveys are available for projects in the Jabodetabek area.
Conclusion
Reverberation time is not a technical detail that can be deferred until a building is finished. RT60 determines whether listeners at the back can follow a presentation without strain, whether a choir sounds coherent, and whether the PA system that was installed at significant cost can actually perform as intended.
The correct target differs by function, and a multipurpose hall demands more careful design precisely because it has to serve several functions at once. Corrections made without simulation and field measurement risk producing a room that is over-treated or still off target.
If your auditorium or hall is in the planning stage, undergoing renovation, or already in operation but not performing acoustically as expected, the right first step is a field RT60 measurement, not an immediate material installation.
Discuss your auditorium’s RT60 targets and acoustic layout with the Dewa Peredam Ruangan team through the consultation form. Free site surveys are available for the Jabodetabek area, and the engineering team is ready to discuss project requirements outside that region.